This protects for the printhead to prevent wear. The width of the roll varies based on the width of the labels and should always be slightly wider. The ribbon used in the printer consists of wax or resin-based ink on a plastic film called the carrier that is rolled onto a cardboard core. Refer to the article Identify Type of Media. For non-ribbon applications, a heat-sensitive label referred to as a Direct Thermal label must be used. Thermal Transfer is used when the ribbon is required , while Direct Thermal refers to applications that do not use ribbon. Printing can be done with and without ribbon, and the printer (driver or software) must be configured appropriately. The network configuration for the print server has now been completed and the printer installed on the workstation.The printer can be used for a wide variety of printing applications. You can then click the button named "Close" to close the Zebra Setup Utilities program. Once the printer driver and definition have been installed, you will see the newly created printer definition in the Zebra Setup Utilities shown below.Uncheck the option box named "Launch installation of Zebra Font Downloader Setup Wizard" and the click the button named "Finish".You will now see a new port named "LAN_192.168.12.240" with the new static IP address and it will be highlighted.Enter the new static IP address in the fields named "Name:" and "Printer Name or IP Address" and then click the button named "OK".Click on that printer name and then click the button named "Next". In the pane titled "Printers:", scroll down until you get to one named "ZDesigner ZD410-203dpi ZPL".Click the button named "Install New Printer".Click the option box for "Run Zebra Setup Utilities now" and then click the button named "Finish".Click the option box for "I have read the information above" and then click the button named "Next".Check the box for "I accept the terms of the license agreement" and then click the button named "Next".You may be presented with a User Account Control prompt, if so click "Yes".Once the download has completed, open the installer by clicking on it.Click the button named "ACCEPT AND BEGIN DOWNLOAD NOW".Download the drivers for the Zebra ZD410 tag printer by clicking here.If the changes took effect, you will now see the status screen with the new static IP address for the network print server.Enter the new static IP address for the network print server in your web browser and navigate to it to make sure that the changes that were made took effect.Give the reset about a minute to complete. The changes to the network print server will now be applied.Click the button named "Yes" to reset the device.Click the link named "The unit must be reset for new values to take effect.".Click the button named "Submit Changes".Uncheck the box for the option named "Default Address Enabled".This will change the network print server to now have a static IP address instead of one that is obtained via DHCP. Click the drop down box named "IP Protocol" and then click "permanent".In this situation, we will change it to 192.168.12.240. Change the IP Address to what you want it to be.Under the section named "Print Server Configuration, click the link named "TCP/IP Configuration".Once both have been entered, click "Sign in". The username is "admin" and the password is "1234". You will now be prompted to enter the username and password.Under the section named "Status and Configuration", click the link named "Print Server".Under the section named "Printer Home Page", click the link named "Print Server Settings".This IP Address now has admin access to the restricted printer pages. When prompted to enter the password for the print server, enter "1234" and then click "Submit Changes".Under the section named "Printer Home Page", click the link named "View and Modify Printer Settings".Open a web browser and enter the IP address listed in the Network Configuration print out.In the above image, we see that the tag printer is getting an IP address via DHCP of 192.168.12.94.Please note that by default, a new tag printer will obtain an IP address via DHCP. This will print out a configuration page as shown below. Once the tag printer has finished powering on, press and hold the Feed and Cancel buttons for two seconds and then release.Power the tag printer on by pressing and holding the power button for about 5 seconds and then release the power button.Plug the power adapter into the rear of the tag printer and then plug the power cable into an available AC outlet.Connect the other end of the network cable into an available port on your network.Connect a network cable to the rear of the tag printer.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |